Difference between revisions of "Installation/Linux/OpenFOAM-1.7.1/openSUSE"

From OpenFOAMWiki
m (openSUSE 12.1: bigger focus on "this is still being re-written")
(openSUSE 12.1: Updated a bit the instructions, although there is still a lot to confirm)
Line 23: Line 23:
 
<li>Switch to ''root'' mode (administrator) and install the necessary packages (run one line at a time):
 
<li>Switch to ''root'' mode (administrator) and install the necessary packages (run one line at a time):
 
<bash>su -
 
<bash>su -
yum groupinstall 'Development Tools'
+
zypper install -t pattern devel_C_C++
yum install openmpi openmpi-devel qt-devel qt-webkit-devel zlib-devel cmake
+
zypper install gcc-4.5 g++-4.5 cmake libqt4-devel gnuplot openmpi-devel
 
exit
 
exit
 
</bash></li>
 
</bash></li>
 +
 +
<li>TODO: Now, since we're trying to minimize the number of packages to be built, the Open-MPI build that is available with openSUSE is going to be used. The downside </li>
 +
 +
 
<li>Download and unpack (here you can copy-paste all in single go):
 
<li>Download and unpack (here you can copy-paste all in single go):
 
<bash>#OpenFOAM downloading and installation
 
<bash>#OpenFOAM downloading and installation
Line 32: Line 36:
 
mkdir OpenFOAM
 
mkdir OpenFOAM
 
cd OpenFOAM
 
cd OpenFOAM
wget "http://downloads.sourceforge.net/foam/OpenFOAM-2.1.1.tgz?use_mirror=mesh" -O OpenFOAM-2.1.1.tgz
+
wget "http://downloads.sourceforge.net/foam/OpenFOAM-1.7.1.tgz?use_mirror=mesh" -O OpenFOAM-1.7.1.tgz
wget "http://downloads.sourceforge.net/foam/ThirdParty-2.1.1.tgz?use_mirror=mesh" -O ThirdParty-2.1.1.tgz
+
wget "http://downloads.sourceforge.net/foam/ThirdParty-1.7.1.tgz?use_mirror=mesh" -O ThirdParty-1.7.1.tgz
  
tar xzf OpenFOAM-2.1.1.tgz  
+
tar xzf OpenFOAM-1.7.1.tgz  
tar xzf ThirdParty-2.1.1.tgz  
+
tar xzf ThirdParty-1.7.1.tgz  
 
</bash></li>
 
</bash></li>
<li>For building OpenFOAM itself, it depends on whether you have installed the i386 or x86_64 architecture of Fedora. To check this, run:
+
<li>For building OpenFOAM itself, it depends on whether you have installed the i386 or x86_64 architecture of openSUSE. To check this, run:
 
<bash>uname -m</bash>
 
<bash>uname -m</bash>
 
Now, accordingly:
 
Now, accordingly:
 
<ul>
 
<ul>
 
<li>For i386:
 
<li>For i386:
<bash>#forcefully load Open-MPI into the environment
+
<bash>#here you can change 4 to the number of cores you've got
module load openmpi-i386
+
 
+
#here you can change 4 to the number of cores you've got
+
 
source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc WM_NCOMPPROCS=4 WM_MPLIB=SYSTEMOPENMPI WM_ARCH_OPTION=32
 
source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc WM_NCOMPPROCS=4 WM_MPLIB=SYSTEMOPENMPI WM_ARCH_OPTION=32
  
echo "module load openmpi-i386" >> $HOME/.bashrc
 
 
echo "source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc $FOAM_SETTINGS" >> $HOME/.bashrc
 
echo "source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc $FOAM_SETTINGS" >> $HOME/.bashrc
 
</bash></li>
 
</bash></li>
  
 
<li>For x86_64:
 
<li>For x86_64:
<bash>#forcefully load Open-MPI into the environment
+
<bash>#here you can change 4 to the number of cores you've got
module load openmpi-x86_64     
+
 
+
#here you can change 4 to the number of cores you've got
+
 
source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc WM_NCOMPPROCS=4 WM_MPLIB=SYSTEMOPENMPI
 
source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc WM_NCOMPPROCS=4 WM_MPLIB=SYSTEMOPENMPI
  
echo "module load openmpi-x86_64" >> $HOME/.bashrc
 
 
echo "source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc $FOAM_SETTINGS" >> $HOME/.bashrc</bash>
 
echo "source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc $FOAM_SETTINGS" >> $HOME/.bashrc</bash>
 
</li>
 
</li>
Line 68: Line 64:
 
('''Warning''': this may take somewhere from 30 minutes to 6 hours, depending on your machine.)<br>
 
('''Warning''': this may take somewhere from 30 minutes to 6 hours, depending on your machine.)<br>
 
<bash>#Go into OpenFOAM's main source folder
 
<bash>#Go into OpenFOAM's main source folder
cd OpenFOAM-2.1.1
+
cd OpenFOAM-1.7.1
  
 
# This next command will take a while... somewhere between 30 minutes to 3-6 hours.
 
# This next command will take a while... somewhere between 30 minutes to 3-6 hours.
Line 93: Line 89:
 
<li>Now, in order to build ParaView 3.10.1 that comes with OpenFOAM:
 
<li>Now, in order to build ParaView 3.10.1 that comes with OpenFOAM:
 
<bash>cd $WM_THIRD_PARTY_DIR
 
<bash>cd $WM_THIRD_PARTY_DIR
sed -i -e 's/ClearAndSelect = Clear | Select/ClearAndSelect = static_cast<int>(Clear) | static_cast<int>(Select)/' \
 
ParaView-3.12.0/Qt/Core/pqServerManagerSelectionModel.h
 
 
./makeParaView -qmake $(which qmake-qt4)
 
./makeParaView -qmake $(which qmake-qt4)
  
Line 102: Line 96:
 
./Allwmake
 
./Allwmake
 
</bash></li>
 
</bash></li>
<li>Now you can go read the User Guide: [http://www.openfoam.org/docs/user/ official OpenFOAM User Guide]</li>
+
<li>Now you can go read the User Guide, which is located at <tt>$HOME/OpenFOAM/OpenFOAM-1.7.1/doc/Guides-a4/UserGuide.pdf</tt>.</li>
 
</ol>
 
</ol>
  

Revision as of 10:55, 19 August 2012

1 Introduction

This page is dedicated to explaining how to install OpenFOAM OF Version 171.png in openSUSE.


2 Copy-Paste steps

A few notes before you start copy-pasting:

  1. Lines that start with # don't have to be copy-pasted. They are just comments to let you know what's going on.
  2. One wrong character is enough for breaking this guide, so make sure you can read the characters properly or that the installed language system does not break the copied characters!

2.1 openSUSE 12.1

NOTE: These instructions are still being re-written from a pseudo-template page!


Discussion thread where you can ask questions about these steps: Install OpenFOAM-1.7.1 on openSUSE 12.1

Steps:

  1. Switch to root mode (administrator) and install the necessary packages (run one line at a time):
    su -
    zypper install -t pattern devel_C_C++
    zypper install gcc-4.5 g++-4.5 cmake libqt4-devel gnuplot openmpi-devel
    exit
  2. TODO: Now, since we're trying to minimize the number of packages to be built, the Open-MPI build that is available with openSUSE is going to be used. The downside

  3. Download and unpack (here you can copy-paste all in single go):
    #OpenFOAM downloading and installation
    cd ~
    mkdir OpenFOAM
    cd OpenFOAM
    wget "http://downloads.sourceforge.net/foam/OpenFOAM-1.7.1.tgz?use_mirror=mesh" -O OpenFOAM-1.7.1.tgz
    wget "http://downloads.sourceforge.net/foam/ThirdParty-1.7.1.tgz?use_mirror=mesh" -O ThirdParty-1.7.1.tgz
     
    tar xzf OpenFOAM-1.7.1.tgz 
    tar xzf ThirdParty-1.7.1.tgz
  4. For building OpenFOAM itself, it depends on whether you have installed the i386 or x86_64 architecture of openSUSE. To check this, run:
    uname -m

    Now, accordingly:

    • For i386:
      #here you can change 4 to the number of cores you've got
      source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc WM_NCOMPPROCS=4 WM_MPLIB=SYSTEMOPENMPI WM_ARCH_OPTION=32
       
      echo "source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc $FOAM_SETTINGS" >> $HOME/.bashrc
    • For x86_64:
      #here you can change 4 to the number of cores you've got
      source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc WM_NCOMPPROCS=4 WM_MPLIB=SYSTEMOPENMPI
       
      echo "source $HOME/OpenFOAM/OpenFOAM-2.1.1/etc/bashrc $FOAM_SETTINGS" >> $HOME/.bashrc
  5. Now let's build OpenFOAM:
    (Warning: this may take somewhere from 30 minutes to 6 hours, depending on your machine.)
    #Go into OpenFOAM's main source folder
    cd OpenFOAM-1.7.1
     
    # This next command will take a while... somewhere between 30 minutes to 3-6 hours.
    ./Allwmake > make.log 2>&1
     
    #Run it a second time for getting a summary of the installation
    ./Allwmake > make.log 2>&1
  6. To check if everything went well:
    #Check if icoFoam is working
    icoFoam -help
     
    #Edit the file "make.log" and check if there are any error messages
    #Example:
    gedit make.log
     
    #Create a tarball in case you've seen any errors (it's the first error that matters)
    #or if you don't understand the output
    #and attach the file "make.log.tar.gz" to a post in the designated thread
    tar -czf make.log.tar.gz make.log
  7. Now, in order to build ParaView 3.10.1 that comes with OpenFOAM:
    cd $WM_THIRD_PARTY_DIR
    ./makeParaView -qmake $(which qmake-qt4)
     
    cd $FOAM_UTILITIES/postProcessing/graphics/PV3Readers 
    wmSET $FOAM_SETTINGS
    ./Allwclean 
    ./Allwmake
  8. Now you can go read the User Guide, which is located at $HOME/OpenFOAM/OpenFOAM-1.7.1/doc/Guides-a4/UserGuide.pdf.

Designated discussion thread where you can ask questions about these steps: Install OpenFOAM-1.7.1 on openSUSE 12.1