Difference between revisions of "Installation/Linux/foam-extend-3.0/CentOS SL RHEL"

From OpenFOAMWiki
(Copy-pasted-adapted from 1.6-ext)
 
(Updated links to the new foam-extend-3.0 repo and respective mirrors)
Line 29: Line 29:
 
* You can install from source, by either:
 
* You can install from source, by either:
 
** Following the available official instructions from one of these repositories:
 
** Following the available official instructions from one of these repositories:
*** [http://sourceforge.net/p/openfoam-extend/OpenFOAM-1.6-ext/ci/master/tree/doc/buildInstructions/Centos/5.5 Building Instructions for CentOS 5.5 at the official Extend repository]
+
*** [http://sourceforge.net/p/openfoam-extend/foam-extend-3.0/ci/master/tree/doc/buildInstructions/Centos/5.5 Building Instructions for CentOS 5.5 at the official Extend repository]
*** [http://repo.or.cz/w/openfoam-extend-OpenFOAM-1.6-ext.git/tree/master:/doc/buildInstructions/Centos/5.5 Building Instructions for CentOS 5.5 at repo.or.cz mirror]
+
*** [http://repo.or.cz/w/foam-extend-3.0.git/tree/master:/doc/buildInstructions/Centos/5.5 Building Instructions for CentOS 5.5 at repo.or.cz mirror]
*** [https://github.com/Unofficial-Extend-Project-Mirror/openfoam-extend-OpenFOAM-1.6-ext/tree/master/doc/buildInstructions/Centos/5.5 Building Instructions for CentOS 5.5 at Unofficial-Extend-Project-Mirror@github mirror]
+
*** [https://github.com/Unofficial-Extend-Project-Mirror/openfoam-extend-foam-extend-3.0/tree/master/doc/buildInstructions/Centos/5.5 Building Instructions for CentOS 5.5 at Unofficial-Extend-Project-Mirror@github mirror]
 
*** '''Note''': Before following any of the instructions above, check the section [[../#Note regarding foam-extend-3.0|Note regarding foam-extend-3.0]]
 
*** '''Note''': Before following any of the instructions above, check the section [[../#Note regarding foam-extend-3.0|Note regarding foam-extend-3.0]]
  
 
[[Category:Installing OpenFOAM on Linux]] [[Category:Installing OpenFOAM on CentOS]]
 
[[Category:Installing OpenFOAM on Linux]] [[Category:Installing OpenFOAM on CentOS]]

Revision as of 00:12, 11 January 2014

1 Introduction

This page is dedicated to explaining how to install the foam-extend project OF Version 30ext.png in:

  • Community ENTerprise Operating System, aka CentOS.
  • Red Hat Enterprise Linux, aka RHEL.
  • Scientific Linux, aka SL.

In theory, all of the above follow the same versioning.

Both SL and CentOS derive from RHEL, but CentFOAM is what inspired this page. Therefore, before even trying to follow the instructions on this page, try first CentFOAM.

Last but not least, RHEL uses Fedora as their bleeding edge Linux Distribution, where they test new features. This leads to very close similarities between them, e.g. RHEL 6.3 is very similar to Fedora 14; which means that whatever you can build on Fedora 14, you should also be able to build on RHEL 6.3!

If you do not yet feel comfortable using Linux, then perhaps you better first read the page Working with the Shell and train a bit with the shell/terminal environments, so you can have a better perception of the steps shown below.


2 Copy-Paste steps

A few notes before you start copy-pasting:

  1. Lines that start with # don't have to be copy-pasted. They are just comments to let you know what's going on.
  2. One wrong character is enough for breaking this guide, so make sure you can read the characters properly or that the installed language system does not break the copied characters!


2.1 CentOS 5.5

Here you have a few choices: