Difference between revisions of "Installation/Linux/foam-extend-3.2/Ubuntu"
(Python and Python-dev are now a must) |
(Added instructions for Ubuntu 15.10) |
||
Line 40: | Line 40: | ||
Then continue following the instructions on the previous page, subsection [[Installation/Linux/foam-extend-3.2#Installing from source code|Get the source code]]. | Then continue following the instructions on the previous page, subsection [[Installation/Linux/foam-extend-3.2#Installing from source code|Get the source code]]. | ||
+ | |||
+ | |||
+ | == Ubuntu 15.10 == | ||
+ | |||
+ | Run the following command: | ||
+ | <bash>sudo apt-get update</bash> | ||
+ | <bash>sudo apt-get install git-core build-essential binutils-dev cmake flex \ | ||
+ | zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev libiberty-dev \ | ||
+ | libxt-dev rpm mercurial graphviz python python-dev | ||
+ | </bash> | ||
+ | |||
+ | Then follow the instructions on the previous page, subsection [[Installation/Linux/foam-extend-3.2#Installing from source code|Get the source code]], although keep in mind to run the following commands '''before''' you run '''{{tt|source etc/bashrc}}''': | ||
+ | <bash>echo export WM_THIRD_PARTY_USE_BISON_27=1 >> etc/prefs.sh</bash> | ||
+ | |||
+ | More specifically, the commands should be executed something like this: | ||
+ | <bash>cd ~/foam/foam-extend-3.2 | ||
+ | |||
+ | echo export WM_THIRD_PARTY_USE_BISON_27=1 >> etc/prefs.sh | ||
+ | |||
+ | source etc/bashrc</bash> | ||
[[Category:Installing OpenFOAM on Linux]] [[Category:Installing OpenFOAM on Ubuntu]] | [[Category:Installing OpenFOAM on Linux]] [[Category:Installing OpenFOAM on Ubuntu]] |
Revision as of 14:43, 2 January 2016
1 Introduction
This page is dedicated to preparing an Ubuntu system for installing the foam-extend project .
2 Ubuntu versions
2.1 Ubuntu 12.04
Run the following command:
sudo apt-get update
sudo apt-get install git-core build-essential binutils-dev flex \ bison zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev \ libxt-dev rpm mercurial graphviz python python-dev
Then follow the instructions on the previous page, subsection Get the source code, although keep in mind to run the following commands before you run source etc/bashrc:
echo export WM_COMPILER=Gcc49 >> etc/prefs.sh echo export WM_THIRD_PARTY_USE_GCC_492=1 >> etc/prefs.sh echo export compilerInstall=FOAM >> etc/prefs.sh
More specifically, the commands should be executed something like this:
cd ~/foam/foam-extend-3.2 echo export WM_COMPILER=Gcc49 >> etc/prefs.sh echo export WM_THIRD_PARTY_USE_GCC_492=1 >> etc/prefs.sh echo export compilerInstall=FOAM >> etc/prefs.sh source etc/bashrc
2.2 Ubuntu 14.04
Run the following command:
sudo apt-get update
sudo apt-get install git-core build-essential binutils-dev cmake flex \ bison zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev libiberty-dev \ libxt-dev rpm mercurial graphviz python python-dev
Then continue following the instructions on the previous page, subsection Get the source code.
2.3 Ubuntu 15.10
Run the following command:
sudo apt-get update
sudo apt-get install git-core build-essential binutils-dev cmake flex \ zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev libiberty-dev \ libxt-dev rpm mercurial graphviz python python-dev
Then follow the instructions on the previous page, subsection Get the source code, although keep in mind to run the following commands before you run source etc/bashrc:
echo export WM_THIRD_PARTY_USE_BISON_27=1 >> etc/prefs.sh
More specifically, the commands should be executed something like this:
cd ~/foam/foam-extend-3.2 echo export WM_THIRD_PARTY_USE_BISON_27=1 >> etc/prefs.sh source etc/bashrc