Installation/Linux/foam-extend-4.0/Ubuntu

From OpenFOAMWiki
< Installation‎ | Linux‎ | foam-extend-4.0
Revision as of 20:01, 26 April 2019 by Wyldckat (Talk | contribs)

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

1 Introduction

This page is dedicated to preparing an Ubuntu system for installing the foam-extend project OF Version 40ext.png.


2 Ubuntu versions

2.1 Ubuntu 12.04

Run the following commands:

sudo apt-get update
sudo apt-get install git-core build-essential binutils-dev flex \
bison zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev \
libxt-dev rpm mercurial graphviz python python-dev

Then follow the instructions on the previous page, subsection Get the source code, although keep in mind to run the following commands before you run source etc/bashrc:

echo export WM_COMPILER=Gcc49 >> etc/prefs.sh
echo export WM_THIRD_PARTY_USE_GCC_492=1  >> etc/prefs.sh
echo export compilerInstall=FOAM >> etc/prefs.sh

More specifically, the commands should be executed something like this:

cd ~/foam/foam-extend-4.0
 
echo export WM_COMPILER=Gcc49 >> etc/prefs.sh
echo export WM_THIRD_PARTY_USE_GCC_492=1  >> etc/prefs.sh
echo export compilerInstall=FOAM >> etc/prefs.sh
 
source etc/bashrc


2.2 Ubuntu 14.04

Run the following commands:

sudo apt-get update
sudo apt-get install git-core build-essential binutils-dev cmake flex \
bison zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev libiberty-dev \
libxt-dev rpm mercurial graphviz python python-dev

Then continue following the instructions on the previous page, subsection Get the source code.


2.3 Ubuntu 16.04

Run the following commands:

sudo apt-get update
sudo apt-get install git-core build-essential binutils-dev cmake flex \
zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev libiberty-dev \
libxt-dev rpm mercurial graphviz python python-dev

Then follow the instructions on the previous page, subsection Get the source code, although keep in mind to run the following commands before you run source etc/bashrc:

echo export WM_THIRD_PARTY_USE_BISON_27=1  >> etc/prefs.sh

More specifically, the commands should be executed something like this:

cd ~/foam/foam-extend-4.0
 
echo export WM_THIRD_PARTY_USE_BISON_27=1  >> etc/prefs.sh
 
source etc/bashrc


Note: If you are using Ubuntu within WSL, then study this thread: Problems compiling foam-extend-4.0 + fsiFoam on Ubuntu+WSL

2.4 Ubuntu 18.04

Run the following commands:

sudo apt-get update
sudo apt-get install git-core build-essential binutils-dev cmake flex \
zlib1g-dev qt4-dev-tools libqt4-dev libncurses5-dev \
libxt-dev rpm mercurial graphviz python python-dev  gcc-5 g++-5

Then follow the instructions on the previous page, subsection Get the source code, but keep in mind to run a few additional commands before you run source etc/bashrc... More specifically, the commands should be executed something like this:

cd ~/foam/foam-extend-4.0
 
echo export WM_THIRD_PARTY_USE_BISON_27=1  >> etc/prefs.sh
echo export QT_SELECT=qt4  >> etc/prefs.sh
echo "export WM_CC='gcc-5'"  >> etc/prefs.sh
echo "export WM_CXX='g++-5'"  >> etc/prefs.sh
echo "export QT_BIN_DIR=/usr/bin/" >> etc/prefs.sh
 
source etc/bashrc

Then before running Allwmake.firstInstall, run the following commands:

sed -i -e 's=rpmbuild --define=rpmbuild --define "_build_id_links none" --define=' ThirdParty/tools/makeThirdPartyFunctionsForRPM
sed -i -e 's/gcc/\$(WM_CC)/' wmake/rules/linux64Gcc/c
sed -i -e 's/g++/\$(WM_CXX)/' wmake/rules/linux64Gcc/c++