Difference between revisions of "Installation/swak4Foam/Installing On/Ubuntu"
From OpenFOAMWiki
< Installation | swak4Foam | Installing On
(Kick started this page, but this still needs some considerable tweaking...) |
(OK, generic instructions are up. The rest has been deferred to the other wiki pages.) |
||
| Line 19: | Line 19: | ||
'''Discussion thread where you can ask questions about these steps''': ''None available at the moment.'' | '''Discussion thread where you can ask questions about these steps''': ''None available at the moment.'' | ||
| − | |||
Steps: | Steps: | ||
<ol> | <ol> | ||
| Line 25: | Line 24: | ||
<bash>sudo apt-get install build-essential bison flex</bash> | <bash>sudo apt-get install build-essential bison flex</bash> | ||
</li> | </li> | ||
| − | <li> | + | <li>Now, to download and unpack {{tt|swak4Foam}}, please follow the respective instructions from this page: [[Installation/swak4Foam/Downloading]] - once you've completed the download and unpacking process, then you can proceed to the following step. |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
</li> | </li> | ||
<li>Now let's build {{tt|swak4Foam}}: | <li>Now let's build {{tt|swak4Foam}}: | ||
| Line 42: | Line 37: | ||
</bash></li> | </bash></li> | ||
| − | <li> | + | <li>If you're not familiar with OpenFOAM's build process, namely to check if everything built as intended, then check the instructions given at this page: [[Installation/swak4Foam/Understanding Error Messages]] |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
</li> | </li> | ||
| − | <li> | + | <li>If everything went well, then head onto the main {{tt|swak4Foam}} page: [[Contrib/swak4Foam]]</li> |
| − | + | ||
| − | + | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
</ol> | </ol> | ||
Revision as of 13:00, 22 March 2014
1 Introduction
This page is dedicated to explaining how to install swak4Foam in Ubuntu.
If you do not yet feel comfortable using Linux, then perhaps you better first read the page Working with the Shell and train a bit with the shell/terminal environments, so you can have a better perception of the steps shown below.
2 Copy-Paste steps
A few notes before you start copy-pasting:
- Lines that start with # don't have to be copy-pasted. They are just comments to let you know what's going on.
- One wrong character is enough for breaking this guide, so make sure you can read the characters properly or that the installed language system does not break the copied characters!
2.1 Ubuntu 12.04
Discussion thread where you can ask questions about these steps: None available at the moment.
Steps:
- Install the necessary packages:
sudo apt-get install build-essential bison flex
- Now, to download and unpack swak4Foam, please follow the respective instructions from this page: Installation/swak4Foam/Downloading - once you've completed the download and unpacking process, then you can proceed to the following step.
- Now let's build swak4Foam:
#Go into swak4Foam's main source folder cd swak4Foam # This next command will take a while... ./Allwmake > make.log 2>&1 #Run it a second time for getting a summary of the installation ./Allwmake > make.log 2>&1
- If you're not familiar with OpenFOAM's build process, namely to check if everything built as intended, then check the instructions given at this page: Installation/swak4Foam/Understanding Error Messages
- If everything went well, then head onto the main swak4Foam page: Contrib/swak4Foam
Discussion thread where you can ask questions about these steps: None available at the moment.
