Difference between revisions of "Installation/Linux/foam-extend-3.2/openSUSE"
From OpenFOAMWiki
< Installation | Linux | foam-extend-3.2
(→openSUSE 42.1: mercurial and rpm-build are also needed) |
m (moved note into steps) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 14: | Line 14: | ||
<li>Install the necessary packages: | <li>Install the necessary packages: | ||
<bash>zypper install -t pattern devel_C_C++ | <bash>zypper install -t pattern devel_C_C++ | ||
| − | zypper install cmake libqt4-devel qt4-x11-tools qt4-assistant-adp-devel gnuplot openmpi-devel boost-devel cgal-devel gmp-devel mpfr | + | zypper install cmake libqt4-devel qt4-x11-tools qt4-assistant-adp-devel gnuplot openmpi-devel boost-devel cgal-devel gmp-devel mpfr-devel libQtWebKit-devel python-devel git mercurial rpm-build |
</bash></li> | </bash></li> | ||
{{Installation/Linux/ExitRoot}} | {{Installation/Linux/ExitRoot}} | ||
| + | |||
| + | <li>'''Note''': In order for Open-MPI to be properly accessible, you will need to either logout and then log back in or run the following command in each terminal in the meantime: | ||
| + | <bash>source /etc/profile.d/mpi-selector.sh</bash> | ||
| + | </li> | ||
</ol> | </ol> | ||
| Line 23: | Line 27: | ||
<bash>echo unset WM_THIRD_PARTY_USE_CMAKE_322 >> etc/prefs.sh | <bash>echo unset WM_THIRD_PARTY_USE_CMAKE_322 >> etc/prefs.sh | ||
echo export WM_MPLIB=SYSTEMOPENMPI >> etc/prefs.sh | echo export WM_MPLIB=SYSTEMOPENMPI >> etc/prefs.sh | ||
| − | + | </bash> | |
More specifically, the commands should be executed something like this: | More specifically, the commands should be executed something like this: | ||
| Line 30: | Line 34: | ||
echo unset WM_THIRD_PARTY_USE_CMAKE_322 >> etc/prefs.sh | echo unset WM_THIRD_PARTY_USE_CMAKE_322 >> etc/prefs.sh | ||
echo export WM_MPLIB=SYSTEMOPENMPI >> etc/prefs.sh | echo export WM_MPLIB=SYSTEMOPENMPI >> etc/prefs.sh | ||
| − | |||
source etc/bashrc</bash> | source etc/bashrc</bash> | ||
| + | And then, in order for the library {{tt|parMetisDecomp}} to build properly, you need to run once the following command: | ||
| + | <bash>sed -i -e 's=\-L$(OPENMPI.*=$(PLIBS)=' $FOAM_SRC/decompositionMethods/parMetisDecomp/Make/options</bash> | ||
| + | |||
| + | '''Note''': Using the openSUSE's own Metis system installation did not work at the time of this writing (23:09, 19 December 2015 (CET)). | ||
[[Category:Installing OpenFOAM on Linux]] [[Category:Installing OpenFOAM on openSUSE]] | [[Category:Installing OpenFOAM on Linux]] [[Category:Installing OpenFOAM on openSUSE]] | ||
Latest revision as of 20:08, 26 March 2017
1 Introduction
This page is dedicated to preparing an openSUSE system for installing the foam-extend project 
.
2 openSUSE versions
2.1 openSUSE 42.1
Follow these steps:
- Switch to root mode (administrator), to install the necessary packages:
sudo -s
- If the 'sudo' command tells you're not in the sudoers list, then run:
su -
- If the 'sudo' command tells you're not in the sudoers list, then run:
- Install the necessary packages:
zypper install -t pattern devel_C_C++ zypper install cmake libqt4-devel qt4-x11-tools qt4-assistant-adp-devel gnuplot openmpi-devel boost-devel cgal-devel gmp-devel mpfr-devel libQtWebKit-devel python-devel git mercurial rpm-build
- Now exit from the root mode:
exit - Note: In order for Open-MPI to be properly accessible, you will need to either logout and then log back in or run the following command in each terminal in the meantime:
source /etc/profile.d/mpi-selector.sh
Then continue following the instructions on the previous page, subsection Get the source code, although keep in mind to run the following commands before you run source etc/bashrc:
echo unset WM_THIRD_PARTY_USE_CMAKE_322 >> etc/prefs.sh echo export WM_MPLIB=SYSTEMOPENMPI >> etc/prefs.sh
More specifically, the commands should be executed something like this:
cd ~/foam/foam-extend-3.2 echo unset WM_THIRD_PARTY_USE_CMAKE_322 >> etc/prefs.sh echo export WM_MPLIB=SYSTEMOPENMPI >> etc/prefs.sh source etc/bashrc
And then, in order for the library parMetisDecomp to build properly, you need to run once the following command:
sed -i -e 's=\-L$(OPENMPI.*=$(PLIBS)=' $FOAM_SRC/decompositionMethods/parMetisDecomp/Make/options
Note: Using the openSUSE's own Metis system installation did not work at the time of this writing (23:09, 19 December 2015 (CET)).
